ANSYS如何选择一个范围内的所有体(使用vsel,s,loc,x)因为需要在柱体坐标下选择一个柱状体内所有的体,可是每次都不能选择正确,请问应该如何设置!其中vsel,s,loc,x的x对应的是柱体坐标的

来源:学生作业帮助网 编辑:作业帮 时间:2024/05/13 09:16:01

ANSYS如何选择一个范围内的所有体(使用vsel,s,loc,x)因为需要在柱体坐标下选择一个柱状体内所有的体,可是每次都不能选择正确,请问应该如何设置!其中vsel,s,loc,x的x对应的是柱体坐标的
ANSYS如何选择一个范围内的所有体(使用vsel,s,loc,x)
因为需要在柱体坐标下选择一个柱状体内所有的体,可是每次都不能选择正确,请问应该如何设置!其中vsel,s,loc,x的x对应的是柱体坐标的半径

ANSYS如何选择一个范围内的所有体(使用vsel,s,loc,x)因为需要在柱体坐标下选择一个柱状体内所有的体,可是每次都不能选择正确,请问应该如何设置!其中vsel,s,loc,x的x对应的是柱体坐标的
Type
Label identifying the type of volume select:
S — Select a new set (default).
R — Reselect a set from the current set.
A — Additionally select a set and extend the current set.
U — Unselect a set from the current set.
ALL — Restore the full set.
NONE — Unselect the full set.
INVE — Invert the current set (selected becomes unselected and vice versa).
STAT — Display the current select status.
The following fields are used only with Type = S,R,A,or U:
Item
Label identifying data.Valid item labels are shown in the table below.Some items also require a component label.If Item = PICK (or simply “P”),graphical picking is enabled and all remaining command fields are ignored (valid only in the GUI).Defaults to VOLU.
Comp
Component of the item (if required).Valid component labels are shown in the table below.
VMIN
Minimum value of item range.Ranges are volume numbers,coordinate values,attribute numbers,etc.,as appropriate for the item.A component name (as specified on the CM command) may also be substituted for VMIN (VMAX and VINC are ignored).If Item = MAT,TYPE,REAL,or ESYS and if VMIN is positive,the absolute value of Item is compared against the range for selection; if VMIN is negative,the signed value of Item is compared.See the VLIST command for a discussion of signed attributes.
VMAX
Maximum value of item range.VMAX defaults to VMIN.
VINC
Value increment within range.Used only with integer ranges (such as for volume numbers).Defaults to 1.VINC cannot be negative.
KSWP
Specifies whether only volumes are to be selected:
0 — Select volumes only.
1 — Select volumes,as well as keypoints,lines,areas,nodes,and elements associated with selected volumes.Valid only with Type = S.
Command Default
All volumes are selected.
Notes
Selects volumes based on values of a labeled item and component.For example,to select a new set of volumes based on volume numbers 1 through 7,use VSEL,S,VOLU,1,7.The subset is used when the ALL label is entered (or implied) on other commands,such as VLIST,ALL.Only data identified by volume number are selected.Data are flagged as selected and unselected; no data are actually deleted from the database.
This command is valid in any processor.
For Selects based on non-integer numbers (coordinates,results,etc.),items that are within the range VMIN-Toler and VMAX+Toler are selected.The default tolerance Toler is based on the relative values of VMIN and VMAX as follows:
If VMIN = VMAX,Toler = 0.005 x VMIN.
If VMIN = VMAX = 0.0,Toler = 1.0E-6.
If VMAX ≠ VMIN,Toler = 1.0E-8 x (VMAX-VMIN).
Use the SELTOL command to override this default and specify Toler explicitly.
VSEL - Valid Item and Component Labels
VSELType,Item,Comp,VMIN,VMAX,VINC,KABS
Item Comp Description
VOLU Volume number.
LOC X,Y,Z X,Y,or Z center (picking "hot spot" location in the active coordinate system).
MAT Material number associated with the volume.
TYPE Element type number associated with the volume.
REAL Real constant set number associated with the volume.
ESYS Element coordinate system associated with the volume.
Menu Paths
Utility Menu>Select>Entities
这是详细的选择体说明!

VSEL,S,LOC,X,0,r
X 后面要指定范围,即选择的是从0到r范围内的体。

ANSYS如何选择一个范围内的所有体(使用vsel,s,loc,x)因为需要在柱体坐标下选择一个柱状体内所有的体,可是每次都不能选择正确,请问应该如何设置!其中vsel,s,loc,x的x对应的是柱体坐标的 ansys中如何选择所有重合的节点 ANSYS如何选择Z=0平面上0-30°范围内的节点 在ansys中如何方便的选择一个面 Ansys中如何选择一个复杂物体的多个面,也就是怎样选择一个体后能把它的面都选上? ansys中如何选择面及其上的节点 ANSYS中如何选择需要折减强度的单元? 如何选择ansys单元类型选择? ANSYS如何提取所有子步中位移 ansys如何选择某一体上面的某根线如题,用选择命令,划分网格需要选择某一特定体上面的某一根特定的线 ansys 瞬态热分析中,如何给装配体中的某一个零件的所有节点施加相同的温度? ansys workbench里我要选择一个复杂的面,并命名,该面是一个水管的内壁面,内径已知,在ansys classic中可以通过lsel,s,radius来解决,可是workbench如何解决呢? 在ANSYS中的载荷如何施加在ANSYS中,要在一个圆环体的内圆边界上加载集中力,要如何进行? 怎么把workbench模型导入ansys,还有一个问题,装配体如何调入ansys workbench ansys 如何加载一个随时间变化的力rt 在ansys中如何加载一个周期性变化的力 ansys加载荷的时候,节点太多,不好选择,能通过坐标选择吗?该如何选择? ANSYS热分析完成后,如何在后处理中查看所有结点的平均温度?